-
Want a new pair of hoops? Here’s how to turn two pieces of wire into a unique pair of wiggle hoop earrings.
Want to work with metal but don’t want to invest in all the equipment? Then this tutorial is for you! Follow along to make a unique pair of wiggle hoop earrings using pliers and some wire. I love how simple but stunning this tutorial is. Please note that this tutorial contains affiliate links from which we may receive a small commission.
You’ll need the following tools and materials to make your wiggle hoop earrings:
1: Two pieces of wire, I used 0.8mm diameter sterling silver and cut mine to be about 18cm long each.
You can get silver wire here:
If you’re feeling fancy, you can get solid gold wire here:
2: A jewellery file or emery paper to ensure that the ends of the wire aren’t too sharp.
You can get a jewellery file here:
I have my emery paper attached to a stick for more control. You can get some here:
3: Half round-Flat pliers. These pliers have a half-round side and a flat side to make curves.
You can get a pair here:
4: Round-flat pliers.
You can get a pair here:
5: Parallel pliers.
You can get some here:
6: A bangle mandrel or something else that is the right diameter so you can shape your earrings into a circle.
You can get one here:
7: Butterfly backs.
You can get butterfly backs here:
8: A nylon or leather hammer for shaping the earrings against the mandrel (Don’t use this if you are shaping your earrings around something breakable).
You can get a hammer here:
9: Sticky tape. I used plastic tape but masking tape would likely be more suitable.
You can get masking tape here:
Follow these steps to make your own pair of hoop earrings:
1: File the ends of the wire so that they are flat and have no sharp edges.
2: If you have emery paper, sand the ends as well to further break down any sharp ends.
3: Tape the two pieces of wire together.
4: Take your half round-flat pliers and create the first bend at the end of the wire by clamping the wire into the jaws of the pliers and pressing them together.
5: Flip the pliers around and place them on the other side of the wire and repeat step 4 to make a curve in the wire in the opposite direction.
6: Repeat steps 4 and 5 until your pieces of wire are formed into a squiggle shape, but leave about 1cm at the end for the earring post.
7: Remove the tape and separate the wires.
8: Wrap the wire around the bracelet mandrel to form it into the earring shape. Use the nylon hammer to hammer it into shape. Repeat this for both of the earrings.
9: You can further adjust the shape of the earrings by pressing the half round-flat pliers around the earring, making sure to match the curve of the pliers with the inner curve of the earrings. Doing this will add more tension to your earrings to help them hold their shape.
10: When you are happy with the shape of your hoops, Take the round flat pliers and push the straight ends of the wire around so they sit sideways.
11: Then take your parallel pliers and use them to adjust the straight ends of each earring so that they are centered in the middle of the wiggle to sit evenly in your ears.
12: Once you have adjusted the ends, your earrings are finished and ready to wear. Pop the butterfly backs on to secure them on your lobes.
Here’s how the finished product looks! How will you style yours?
-
Want to make your own hoop earrings out of wire? Here’s how you can do it!
It can be so satisfying to make your own jewellery out of metal, but you might wonder how you can do it without all the tools and fire… well I’ve got an answer for you… here’s how you can make some metal hoop earrings out of wire and a few tools, no fire or expensive tools required! Please note that this tutorial contains affiliate links.
You’ll need these tools and materials for your pair of metal hoop earrings:
1: Two pieces of wire, mine were about 12cm long (I used rose gold-filled wire). The longer the wire is, the bigger your hoops will be. It is helpful to note that longer pieces of wire are easier to work with than shorter pieces.
2: A pair of round flat pliers.
3: A pair of round nose pliers.
4: Cutting pliers to cut your wire to length.
5: Flat nose pliers.
6: A ring mandrel or something round that you can use to form the earring shape.
7: A file.
Follow these steps to make your special metal hoop earrings:
1: File both ends of each piece of wire so that it is flat and smooth, this will make it nicer to put through your ear.
Here is an example of what the filed ends will look like. 2: Take one of the wires and bend one end to form a right angle using the flat round pliers. I used the edge of the flat side to measure out how much to bend.
3: Repeat step 2 for the second wire.
4: Using the round nose pliers, turn the short bent end of each wire into a loop.
5: Take each wire and wrap it around the ring mandrel or round item to form the hoop shape. Press gently around with your fingers or tap lightly with a plastic or leather hammer to get the shape you like. Because my mandrel was a bit small for the length of wire I used, I pulled it gently and let the wire flex back to make a bigger hoop.
Note: pulling the wire tight around the mandrel like this helps give it tension and hold the hoop shape. 
6: Add a small kink to the non-looped end of each earring using flat nose pliers. This will allow the ends to hook into the loops of the hoop.
Now your hoop earrings are finished! How lovely is it that you can make your own precious metal jewellery at home?!
Here are some more tutorials that show you how to make metal wire jewelry without needing a jeweller’s torch:
-
How to make a cute pair of beaded statement earrings!
These earrings are really cute, they are a twist on the typical beaded hoop, as they feature a beaded bar in the centre and are slightly oval in shape. I used some green and blue beads to make this pair of earrings. Please note that this tutorial contains affiliate links.
You’ll need these tools and materials to make these earrings:
1: Two pieces of bracelet sized memory wire, one coil for each earring.
2: Two long eye pins.
3: Two jump rings.
4: Two earring hooks.
5: Beads. I used four plastic blue beads and some green glass beads.
https://www.ebay.com.au/itm/263927947665?hash=item3d7354e191:g:cjMAAOSwrKBgh0ma&frcectupt=true
6: Pliers. I used my cutting pliers, round nose pliers and flat nose pliers.
Follow these steps to make your statement earrings:
1: Add beads to the eye pins in your chosen pattern.
2: Bend the top of the pin to form an angle.
3: Loop the top of the pin using the round nose pliers.
4: Repeat steps 1-3 for the second eye pin.
5: Take one of the pieces of memory wire and loop one end using the round nose pliers.
6: Add beads to the wire. Bead to about half-way through the hoop.
7: Add one of the eye pins to the wire.
8: Add beads to the rest of the memory wire, leaving about 1cm without beads.
9: Loop the other end of the wire using the round nose pliers again. Thread it through the first loop you made before closing it fully.
10: Open the top loop of the eye pin and thread it through the two loops at the top of the hoop. Close it to secure the pin in place.
11: Repeat steps 1-10 for the second earring.
12: Attach an earring hook to each hoop using the jump rings.
Now your statement earrings are finished and ready to wear!! So cute and pretty!
