-
Here’s how to turn some thick wire into a wiggle bangle!
This bangle is so cute! It is a no-heat way to make a unique bangle that you can wear on its own or stacked with other bracelets. Please note that this tutorial contains affiliate links for which we may receive a small commission.
You’ll need the following tools and materials to make your bangle:
1: A piece of thick wire that is about 30-40 cm long (you might need to trim the end or add extra length depending on how large your bracelet needs to be). I used this copper wire that was 1.7mm in diameter.
You can get some copper wire here:
Or if you like, you can make it out of silver wire, which you can get here:
2: A file and emery paper to smooth the ends of the wire.
You can get a file here:
You can get emery paper here:
3: A pair of parallel pliers.
You can get a pair here:
4: A bracelet mandrel.
You can get one here:
5: A nylon or leather hammer. I used this nylon hammer.
You can get a hammer here:
Follow these steps to make your wiggle bracelet:
1: File and emery the ends of your wire using the jewelry file and emery paper, making sure it is smooth and there are no sharp ends.
2: Use the flat nose pliers to create a triangle shape at one end of the wire.
3: Now grip the wire next to the triangle and push the long end of the wire against the pliers to form an angle.
4: Repeat step 3 again to create a zigzag shape.
5: Repeat steps 3 and 4 for the rest of the wire until you have about 1.5cm left of the wire.
6: Form the shape into a circle and create another triangle at the other end that is slightly open.
7: Slip the open end of the bracelet through the triangle you formed at the start.
8: Using the flat nose pliers again, close the second triangle to close off the bangle.
9: Put the bangle on the mandrel and hammer it into a circular shape, gently adjusting it so that it lies flat.
Once you are happy with the shape, you can take your bracelet off the mandrel and pop it on your wrist! How simple and lovely? I am very fond of this simple bangle design. How will you style yours?
Here’s how the finished bangle looks.
-
Do you love the look of knit accessories? Why not try knitting your own bangle?
I’ve previously written an i-cord knitted bracelet tutorial, and this one is kind of similar, but the special twist here is the addition of a wire to give the knit structure so it wears more like a bangle than a bracelet! This simple tutorial requires some basic knitting skills, but I think the results are worth it. Please note that this tutorial contains affiliate links.
You’ll need the following tools and materials to make your knitted bangle:
1: Yarn. I used two leftover yarns, a sliver sparkly mohair and a pink boucle style yarn.
Hot pink yarn:
Sparkly black yarn:
2: A piece of wire. I used some recycled copper wire.
3: Pliers. I used my cutting pliers, flat nose pliers and round nose pliers.
4: Scissors.
5: A darning needle.
6: Two double pointed knitting needles. I used some 8mm needles to give myself a chunky i-cord. The width of your i-cord will depend on the size of your yarn and your needles. I recommend using a thick yarn and needles for a bold bangle. Alternatively, if you don’t like knitting, you can use an i-cord knitting machine.
Alternatively, you can try an i-cord knitting machine
Follow these steps to make your own amazing knitted bangle:
1: Hold the two yarns together.
2: Create a slip knot and add it to the needle, pull the yarn to tighten it around the needle.
3: Cast on two more stitches. After casting on the three stitches, slide them to the other end of the needle and begin knitting the first stitch. Knit the next two stitches. This will start to form a tube. You can see this process a bit in this video.
4: After finishing the first row, slide the stitches to the other end of the needle and repeat the knit pattern you did in step 3.
5: Once you have your desired length, it is time to cast off. To cast off, knit the first stitch onto the second needle, then knit the second stitch, after you slide it onto the next needle, take the first stitch and pull it over the second one, you will now have one stitch on each needle. Repeat this again until you only have one stitch left on the second needle.
6: Leaving the final stitch on the needle, trim the end of the yarn leaving a tail.
7: Remove the needle and then thread the tail through the loop and pull it tight. Now your cast off is complete.
8: Take the wire and start pushing it into the middle of the i-cord.
9: Create a loop on one end of the wire.
9: Form the wire into a large circle shape, this will be the form of your bangle.
10: Trim the excess wire using your cutting pliers, leaving a little excess on the end to allow for the loop.
11: Put the second end through the loop you made at the first end, then loop them together using your round nose pliers.
12: Push the knitted i-cord tube around to cover the loops you made. and then tie the two ends together using the tails you left.
13: Use the needle to weave the tails in and further cover the wire. Trim any excess yarn.
Now your knit bangle is finished and ready to wear! How cute is this design? I love it. I’m planning to make a whole stack to add some fun colourful accessories to my wardrobe.
Here are some other fibre focused jewelry tutorials you can follow:
