-
How to make a cute pearl charm out of wire!
Maybe you’ve got some earrings that you want to change up a bit, like a pair of hoops that could use some extra charm… why not make this tiny pearl pendant out of hammered wire?
You’ll need the following tools and materials to make this little charm:
1: Cutting pliers and round nose pliers.
2: A steel block to hammer on.
3: A hammer. I used a normal hammer but a jewelry hammer might be more appropriate 😉
4: A piece of wire. I used some rose gold-filled wire, approximately 3cm long.
5: Pearl beads. I used these two small white pearls.
6: A file or sandpaper for finishing off the ends of the wire.
Here are the steps to follow to make your cute pearl charm:
1: Cut the wire to the length you want it, make sure you leave enough room for hammering and curling the top of the wire.
2: Place the wire on the hammering block.
3: Hammer one end of the wire, flipping it over to make sure both sides are even. Keep hammering until the wire is wide enough to stop your bead from falling off.
4: Place the beads on the wire. They should be stopped from sliding off by the newly hammered end.
5: Bend the wire to form a right angle at the top.
6: Loop the wire using the round nose pliers to secure the beads from sliding off the other end.
7: File or sand the hammered end of the wire to ensure that there are no sharp edges.
Now your charm is finished! What will you decorate with yours?
If you liked this design, here’s another hammered charm tutorial.
Here are some other hammered earring tutorials
- Hammered wire arch earrings with gemstones
- Simple hammered studs
- Hammer texture threader earrings
- Beaded wire threader earrings
This tutorial contains affiliate links.
-
Hop on the pearl trend with these beaded pearl hoop earrings!
I am loving the pearl jewelry trend right now! Here’s how you can DIY your way into unconventional pearl earrings. Contains affiliate links.
You will need the following tools and materials to make your beaded pearl hoops:
1: Pliers. I used cutting pliers to cut my wire, round nose pliers and flat nose pliers.
2: Some wire. I used this wire that I reclaimed from an old jewelry project.
3: Charm connector stud earrings.
4: Two small jump rings.
5: Two medium jump rings.
6: Two larger jump rings.
7: Two small head pins.
8: Two pearl beads. I used these freshwater pearl beads.
9: Seed beads. I used these mixed glass seed beads.
Follow these steps to make your beaded pearl hoops:
1: Curl the end of the wire to form a loop using the round nose pliers.
2: Add the seed beads to the wire.
3: Once the wire is beaded and there is only about 1cm left of the wire left use the round nose pliers again to curl the end into a loop.
4: Repeat steps one to three for the second piece of wire.
5: Form the beaded wires into circle shapes.
6: Join the ends of the wires using the two small jump rings and then set the hoops aside.
7: Add the pearls to each of the head pins.
8: Create a loop at the top of each pin using the round nose pliers. This will secure the pearls on the pins.
9: Attach each of the pearl charms to the beaded hoops using the medium sized jump rings.
10: Attach the earring posts to the top of the hoops using the largest jump rings.
Once the earring posts are in place they are ready to wear! How cute are they?!
Here’s another pair I made with some green pearls.
-
How to Make Pearl Tassels for Your Hoop Earrings
These pearl tassel hoops are a fun way to get on the pearl jewelry trend! Contains affiliate links.
You’ll need the following tools and materials to make your pearl tassel earrings:
1: Pliers. You will need round nose pliers and flat nose pliers to make these earrings.
2: A pair of small hoop earrings. I used these skinny silver hoops.
3: Two eye pins.
4: Six head pins.
5: Two jump rings.
6: Two pearl beads.
7: Mixed beads for the tassels.
Follow these steps to make your pearl tassel earrings:
1: Add the pearls to each of the eye pins.
2: Loop the ends of the eye pins using the round nose pliers to secure the beads on the pin.
3: Add beads to each of the head pins in your chosen design. Make two of each tassel so that your earrings match.
4: Loop the ends of each head pin with the round nose pliers to secure the beads in place.
5: Add three head pins to one of the jump rings and attach the tassel to the bottom of the pearl charm.
6: Repeat step five for the remaining head pins attaching them to the other pearl charm.
7: Slide a tassel on each hoop earring to finish them off.
How cute are these little hoops? Pop them on and turn heads!
